Why Wireless Control Brightens the Effect of LED Lighting

by | Oct 27, 2015

This article is included in these additional categories:

LED lighting is revolutionizing the lighting industry and creating completely new market conditions. However, unlocking its full potential has been hampered by a lack of simple and easy to install industry standard solutions enabling personal control, energy conservation and compliance with increasingly stringent building standards. To fulfill all of these requirements, LED control based on standardized wireless technology is the order of the day.

With LEDs replacing old lighting technologies, new control capabilities enable building owners to achieve higher energy efficiency rates and increased comfort. Fulfilling this potential requires selecting a suitable control solution. As the lighting market is still evolving, different standards and architectures exist for lighting control to cover the comprehensive requirements of changing colors, dimming, occupancy-based on/off, demand response or sophisticated daylight harvesting.

Stringent Regulations

This goes hand in hand with regulations, such as Title 24, which make intelligent lighting control much more than just an optional additional benefit to energy-saving LED technology. It is prescribed by law and the requirements are extensive. The regulations of the California government require five dimming levels, automatic lighting shut-off controls on every floor, class and conference rooms to be equipped with occupancy control and manually shut-off option, occupancy sensors and controls in corridors, warehouse aisles and open areas to automatically reduce lighting by 50 percent when unoccupied, and demand responsive automatic lighting controls to reduce energy consumption by a minimum of 15 percent— just to name a few.

Besides this, green building certification programs such as LEED call for integrated control of building areas for the achievement of the maximum number of points. Here, the meaning of lighting control is still significant: 30 percent of lighting energy consumption is still wasted on average when rooms are not in use.

The Limits of Wires

One option for installing LED lighting control is a wired system. This is mainly suitable for simple use cases where all lights are connected to the same bus and set to the same light intensity. But wiring complexity grows significantly once the system is required to control a set of lights together. Furthermore, an upgrade from a simple scenario to an advanced control system cannot be implemented without costly changes to the existing wiring and the controller. In addition, it is almost impossible to include sensors, for occupancy detection or daylight harvesting for example, to achieve optimal energy saving rates.

Wireless Flexibility

An alternative to a wired system is wireless control. It has increased in popularity in the last decade due to advances in radio technology and the emergence of standards that enable seamless communication between different devices. The key advantages of wireless control are the ease of upgrading existing buildings and expanding a system at any time. No new control wiring is required for existing lights; they simply have to be upgraded with wireless control units.

Elimination of Batteries

Several standards already exist for wireless communication in a building automation system. The energy harvesting wireless standard is one of the most established. It is defined by the EnOcean Alliance, a consortium of international companies of the building automation industry.

The standard is optimized for ultra-low power communication, which allows the use of battery-less, self-powered sensors and switches. Self-powered switches use kinetic energy to generate a wireless signal for controlling and dimming. Light level or occupancy sensors are powered by miniaturized solar cells that harvest ambient light and convert it to electrical energy.

Holistic Approach

The energy harvesting wireless technology enables a complete wireless LED control system for retrofit projects. Solutions based on this standard include 1–10V LED controllers with and without relay, solar-powered occupancy and light-level sensors, kinetic-powered light switches and a remote commissioning software tool. The controller wirelessly communicates using the energy harvesting radio standard at 902 MHz. Via this protocol, it receives wireless telegrams from all linked self-powered wireless switches and sensors and adjusts its outputs accordingly. It provides a switched output for the supply of connected loads as well as a 1–10V control output to dim connected loads. Multiple fixtures can be daisy-chained; e.g., 20 each 30W fixtures or 10 each 60W fixtures.

This system can support a wireless daylight harvesting application, for example. Daylighting means that the light level is automatically adapted to the amount of available natural light in a room measured by light level sensors. In a typical commercial building, it is possible to save between 20 percent and 30 percent of energy with such an automated control system. An increasing number of industry standards, such as ASHRAE 90.1-2010, or governmental energy code requirements, such as Title 24, require daylighting.

Basis Configuration

The wireless controller supports several usage scenarios. In a very simple configuration, only wireless light switches will be connected for manual control of the lights. If desired, it is possible to configure an auto-off timer which turns the lights off after a certain amount of time as usually used in stairways. Another basic installation can be implemented by connecting occupancy sensors which sense motion in a room and send wireless signals to the controller, which controls LED lighting according to occupancy. Both the standard on/off configuration as well as switching between two dimming levels is possible. The latter case is important in applications where a minimum light level must always be maintained. Instead of an on/off configuration, the occupancy sensors’ signals can also be used to set different dimming levels in the range between 100 percent and 0 percent.

The combination of occupancy sensors and rocker switches enables the user to manually turn on the light, whereas the occupancy sensors automatically switch off the light after a pre-configured period of time when the room is unoccupied. Light can be automatically turned back on if occupancy is detected. In this scenario, the occupancy sensor can also be used to switch between a high and a low illumination level and the switch can be used to switch lights off completely.

Sophisticated Control

The addition of a light level sensor allows the implementation of daylight harvesting based on open loop control. This means that the light sensor, positioned facing a skylight or window, measures the amount of available natural light and regulates the output light level accordingly. The lighting controller will then only add as much artificial light as needed. In a simple configuration, the system will change between two levels, a minimum and a maximum dimming level, depending on light levels reported by the light level sensor and signals from occupancy sensors and switches. In addition, it is possible to set up a more sophisticated daylight harvesting scenario that supports continuous dimming based on five sampling points which can be defined via remote commissioning software. In both scenarios, illumination will change smoothly by means of adjustable speeds which can be independently configured for manual changes via rocker switches and automatic changes based on sensor signals.

Configuration over the Air

More advanced settings, such as thresholds, dimming levels, ramp speeds or timers can be changed wirelessly via a remote commissioning interface. By employing a Windows-based laptop computer equipped with a remote commissioning tool, an installer can locate wireless devices throughout the facility, logically connect the controller to switches and sensors and configure settings in the controller over the air, all completely without physical access. It is also possible to link the LED controller via a central unit or a gateway to a supervisory building automation system like BACnet.

Low Installation Effort

Thanks to wireless technology, all of these scenarios can be set up quite easily at low installation costs and only require a minimum of maintenance. Therefore, building operators can fulfill regulatory requirements and achieve immediate energy savings and increased comfort with low investments and a fast return on investment (ROI). The wireless sensors and switches can be flexibly and optimally positioned without requiring repair to walls or ceilings. Due to the self-powered operation, they even eliminate the need for changing batteries.

The LED controller’s compact size enables flexible installation inside of or next to electrical boxes and fixtures so it can be easily wired out of sight using standard wiring practices. Wireless lighting control also enables a migration path, starting with simple control and expanding the system with advanced functionalities such as scheduling, demand response or remote commissioning later on. As the LEDs can be digitally addressed, they can also communicate with each other and a central control. This enables the building of groups of light which create optimized scenes in accordance with changing situations.

Seamless Communication

Wireless standards offer valuable benefits to LED control by following an integrated approach consisting of accessories, software and easy-to-use commissioning tools — a one-stop-shop for the user. At the same time, they combine control functionalities and networking abilities with a consequently standardized communication. The wireless technology allows users to easily install, retrofit, move and commission LED lighting control even in complex systems achieving large economies of scale.

Matthias Kassner is the product marketing director at EnOcean. He is responsible for defining highly innovative future EnOcean products and product marketing activities for the current portfolio. Before joining EnOcean, Matthias worked for 12 years at Texas Instruments (TI) in various positions. He holds the degree of Diplom Ingenieur in electrical engineering from Technical University Ilmenau.  

Additional articles you will be interested in.

Stay Informed

Get E+E Leader Articles delivered via Newsletter right to your inbox!

This field is for validation purposes and should be left unchanged.
Share This